index :: proto

proto.firmata

Firmata Arduino protocol support

доступно с версии: 0.5

---

информация

Firmata basic protocol support.

методы:

• apin_mapping? query mapping between analog port number and digital pin. Analog messages are numbered 0 to 15, which traditionally refer to the Arduino pins labeled A0, A1, A2, etc. However, these pis are actually configured using "normal" pin numbers in the pin mode message, and when those pins are used for non-analog functions. The analog mapping query provides the information about which pins (as used with Firmata's pin mode message) correspond to the analog channels. Return sequence of messages like: [apin_mapping A# PIN#(, where # is number
  

• capabilities? query pin capabilities. Return sequence of messages like: [pin_info PIN# MODE RESOLUTION(, where # is pin number
  

• firmware? query firmata protocol version. Returns message like: [firmware ARDUINO_FIRMWARE_NAME.ino MAJOR MINOR(
  

• pin_mode sets pin mode.
  параметры:

  • PIN# pin number
    тип: int
    обязательно: True
    

  • MODE pin mode
    тип: symbol
    обязательно: True
    

• pin_state? query pin state. The pin state is any data written to the pin (it is important to note that pin state != pin value). For output modes (digital output, PWM, and Servo), the state is any value that has been previously written to the pin. For input modes, typically the state is zero. However, for digital inputs, the state is the status of the pull-up resistor which is 1 if enabled, 0 if disabled. Returns message like [pin_state PIN# MODE state(, where # is pin number
  параметры:
  • PIN# pin number
    тип: int
    обязательно: True
    
• report_apin turns on/off analog pin (A0-A6) value reporting.
  параметры:

  • ANALOG_PIN analog pin number
    тип: int
    обязательно: True
    

  • VALUE value. If 1 - activates analog reporting, messages like [apin PIN# value( are returned every sampling interval (by default 19ms)
    тип: int
    обязательно: True
    

• report_dport turns on/off digital port value reporting.
  параметры:

  • PORT# digital port number. Port is a group of pins, port 0 refers pins 0-8
    тип: int
    обязательно: True
    

  • VALUE value. If 1 - activates digital port reporting, messages like [dport PORT# value( are returned only on pin value change
    тип: int
    обязательно: True
    

• samp_interval sets sampling interval - how often analog data and i2c data is reported to the client. The default for the arduino implementation is 19ms. This means that every 19ms analog data will be reported and any i2c devices with read continuous mode will be read.
  параметры:
  • TIME time
    тип: int
    единица: ms
    обязательно: True
    

• version? query firmata protocol version. Returns message like: [version MAJOR MINOR(
  

• write_dpin write 1 or 0 to digital pin. Pin mode should be OUTPUT.
  параметры:

  • PIN# pin number
    тип: int
    обязательно: True
    

  • VALUE pin value
    тип: int
    обязательно: True
    

• write_pwm writes PWM (Pulse Width Modulation) value to specified pin.
  параметры:

  • PIN# pin number
    тип: int
    обязательно: True
    

  • VALUE pin value
    тип: int
    обязательно: True
    

входы:

• raw input of bytes from Arduino serial connection
  тип: control

выходы:

• raw byte output to Arduino serial connection and tagged parsed output from Arduino
  тип: control

ключевые слова:

arduino firmata

Авторы: Serge Poltavsky

Лицензия: GPL3 or later